Cleaning Home Iron Yourself

Like several other appliances, irons, especially the steam iron, it must also be cleaned, but not too often.

especially necessary if you ignore the manufacturer’s instructions for using distilled water instead of tap water.

Accordingly, there may be an accumulation of mineral deposits or lime in the base plate and inside your steam iron.

In addition, you can collect dust, dirt, stains, and many burned tissue that can, in turn, stick to clothes when you return them and even leave behind stains.

In addition, oxide particles and dust trapped in the sole can cause wrinkling in the tissues during use of the iron. Dirt and accumulated debris will also decrease iron performance for a period of time.

How to clean a steam iron

Here are some methods that can be useful in processed iron cleaning.

damp cloth
dryer sheets
White vinegar
Sodium bicarbonate
damp cloth: Take a large cloth, dip it in plain water, and drain excess water. Clean shoe with the cloth when heated a little to get rid of dirt from the sole.
damp cloth
For stubborn stains, you can use a small amount of mild detergent and a nylon pad.

Dryer sheets: put the iron set on low and rub some dry leaves on the bottom of the plate until the accumulated dirt and grime is removed.
dry leaf
Finally, the iron in a clean cloth to remove any residue of dry leaves.

White vinegar: Clean the inside of a steam iron pour white vinegar, or equal parts of vinegar and water in the water tank to a full third. The (medium-high setting) and let steam for about 5-10 minutes, so that all the vinegar evaporates.

Related Post  How to Hand Wash Clothes without Detergent ?

White vinegar

Then fill the room with running water and turn on the new iron to help remove deposits and the remaining debris vinegar minerals. Finally, wipe the bottom of the plate and steam holes with a paper towel or clean cloth. It will also help get rid of the rust collected in the steam vents.

You may not have to follow this procedure if your steam iron uses a filter water descaling automatically replaceable. In such cases, make sure to replace the filter as recommended in the manual.

You can also create a cleaning solution for home by mixing equal parts of white vinegar and water, soak a cloth in it, and wipe the base with him. In addition, remove the obstruction of steam holes in the accumulation of starch using a cotton swab moistened with this solution.

Baking soda: Regarding stubborn stains and rust on the iron plate, rub a paste of two tablespoons of baking soda and a little water in the affected area.
Sodium bicarbonate
For best results, apply the paste on a soft cloth, rub on the plate, then wipe with a damp cloth. Instead of water, it is possible to mix the baking soda with white vinegar also.

Toothpaste: Scrub sole dirt with some white toothpaste (not gel).
Finally, wipe with a damp cloth to remove the accumulation of dirt and minerals.

Sal: To clean dirt from the stove, put some salt on a paper towel or a cotton towel and run the iron on it while it is the highest vapor in the off position. Dirt join the salt, leaving the plate clean and bright.

Related Post  How to fillet a fish step by step at Home ?


If you stuck in melted plastic on the bottom, sprinkle a little salt on a piece of aluminum foil and iron it. This should help loosen the plastic bottom.

If it is something of wax you have to shake, turn the plate at the top and run through a regular position. To remove oily substances, dip a small amount of ammonia in a clean cloth and wipe the plate with it, then wipe with a damp cloth.

Needless to say, you can also use iron cleaners available on the market. Those mentioned above, however, are inexpensive, natural, easily accessible and safe to use.

additional suggestions

Before cleaning the iron, make sure it is cold and disconnected.
If you burned while ironing fabric, then immediately place a wet sponge in the affected area. Because of the sudden change in temperature, it should help the skin tissues burn the remains of the sole.
Do not clean the base with a metal scouring pad or steel wool as this will damage the iron, causing scratches. Avoid using abrasive cleaners, too, because it is likely that the coating on the outsole of the plate.
After ironing, remove excess water from the chamber of a steam iron while it is hot to keep it dry and prevent mineral scale buildup. Therefore, empty the tank after each use.
To do their job without ironing clothes and problems better slip you can run it on a piece of wax paper when the iron is hot. In addition, you can also clean the iron running on a waxed paper sprinkled with salt.
Read the manual to learn how to iron clean and maintain the plate to ensure efficiency and longevity.

Related Post  How to make hot chocolate with chocolate syrup and milk ?