Trimming Beard Like a Hero at Home
There are several years the growth of the beard was easy. You just stopped shaving. When his beard ended chin, neck, or somewhere after your chest hair began it was the concern of everyone, and especially their own. Now things are different. People tend to have fewer jobs and diseases, and beard require more sewing. A wild unkempt beard could show his impressive manhood, but you are doing a disservice to datable department, employable, all around accessible. The road is best to keep your facial skin under control. Here’s how.
The first thing you want to do is to wash with a shampoo beard beard and prepare. The conditioner will help soften the beard, making it easier to achieve in two stages.
Barba shampoo ($ 25.50) by Cara M. Natty bigelowchemists.com; beard Air ($ 20) Billy Jealousy, nordstrom.com
After drying, take a brush and run against the grain of the beard, so that the hair up. This will not only make it easier to cut, but will also highlight inconsistencies in length.
Boar Bristle Brush Beard ($ 20) by Zeus, birchbox.com
the third stage
Use your mower to cut all to a uniform length. (It is best to start with a larger guard to prevent accidentally cut too short.) To cut mustache, can run a shorter guard on his upper lip, but the nose will block anything much longer.
Bodygroom 7100 beard trimmer ($ 69.99) by Philips Norelco, target.com
His mustache is more difficult to cut with the guard on the mower, so a better choice (provided you have a steady hand) is to comb all the hair down on the upper lip and use cutting naked machines for cutting all which covers the lip. If you do not have a steady hand, just use the mustache scissors instead.
Beard cutting shears ($ 45) by Mark Beard, beardbrand.com
Now comes the most important part: the cut of the neckline. The best way to endanger his beard cleavage ignores his beard or cut in the wrong place. Stop too close to the bone of the jaw, and making it look like you have a double chin, even if it does not. He went too far in his neck, however, and invited comparisons with wild animals or communist agitators.
The safest bet is to cut the tape one inch above the Adam’s apple. Here, they manage to have both a legitimate beard and a sort of neck. First, take two fingers and place them above the Adam’s apple. Imagine a point that is at the top of the fingers here. Now draw an imaginary line behind each ear; curved lines down at this point, creating a form of “U”. Shave while below this point. Yes, the neckbeard should go.
It is also important to shave anything above this line; Hair must still wrap around the lower jaw and chin. Some guys like to have a “hard stop” in her cleavage beard, which means that the hair slowly this neck and beard do not want to disappear. To do this, you only have to shave below the neck, as if, as is shaving his face.
If you want to remove the beard, however, located just your mower to half the length of your favorite Clipper parameters. Using this short clip, sculpt the neck about an inch around the entire base of the beard. Then you can fade even closer: Divide again to disappear in half an inch of bare skin in this environment, or disappear in three-quarters of your usual mower to fade a half inch beard duration of the first fusion.
Fading requires progressively longer lengths of bare skin and ending with the beard. Want will not fade over an inch of the neck, however, if you’re nervous, just start with the neckline of stop and drive the next time you’re in the barber, ask to show how it will fade.
Stainless steel double edge pen knife ($ 220) Seki Edge, sekiedge.com; Sandalwood shaving soap with a wooden bowl ($ 50) The Art of Shaving, artofshaving.com; Badger Wellington ($ 120) by Truefitt & Hill, truefitt.com
I would head hair, it is necessary to comb the beard. First, apply a good oil to soften beard hair. Then run a comb through his beard to distribute the oil, and the style of his beard in place after adjustment. This will also reveal that deflects happened on while cutting, which can take care of your scissors.